Road Repairs and Pavement Patching in Riverstone, NSW
What is included
What Is Included in Our Road Repairs and Pavement Patching
- We walk the damaged road and mark the failed areas, including cracked, sunken and crumbling sections, with paint.
- The work area is coned off and the edges of each repair are cut square with a saw.
- The failed asphalt is lifted out and carted away, then we dig down until the material underneath is firm.
- Soft or wet base material is dug out and replaced with road base, laid in layers.
- Each layer of road base is compacted with a roller or plate compactor before the next goes on.
- The cut edges are painted with bitumen emulsion so the new asphalt sticks to the old.
- Hot asphalt is placed and raked level to match the road surface, then rolled while it is still hot.
- We check the finished patch for dips where water could sit, sweep up and remove the cones.
Why us
Why Choose Us for Road Repairs and Pavement Patching?
Accountable for every job, long after the day
Every road repairs job is done by the people who will still be here next year.
Tested and signed off before we leave
Everything we touch on your road repairs is tested before we go, you get walked through exactly what was done.
Local asphalt contractors, not a call centre
An asphalt contractor answers the phone and the same faces come back if the job runs over a day.
How the job runs
The base decides whether a patch lasts
The first phone call
Tell us where the road is and what is wrong with it, such as potholes, cracked wheel tracks or a sunken patch. We ask who owns the road, because a council or road authority may need to be asked first. We also ask about the traffic that uses it.
Marking out the repair areas
On site, we mark out each repair area with paint and check how deep the damage goes. Surface cracking can be shallow, but a soft, wet base can mean digging further down. That decides how big each repair is and what goes into it. We agree it with you before any cutting starts.
Repair day and handover
We cut, dig out and rebuild each marked area, then lay and roll the new asphalt level with the road. Before we pack up, we look over each patch for dips and rough edges and sweep the loose stone away. Fresh asphalt is soft while it is hot, so we tell you when traffic can go back on.
Common questions
Frequently Asked Questions
Which suburbs do you cover?
We work across Sydney and the surrounding suburbs, and the service areas page lists twenty-one of them, from Windsor and Richmond in the north-west to Liverpool and Narellan in the south-west. If yours is not listed it is still worth asking, because the list is where we work most often rather than a boundary.
What hours are you open?
We are open Monday to Friday, 8am to 5pm, and closed on Saturday and Sunday. Ring in those hours and tell us the suburb and what the surface is used for.
What is the difference between resurfacing and mill and fill?
Resurfacing lays new asphalt over the existing surface after it has been cleaned and repaired. Mill and fill first grinds off the top layer of old asphalt, then lays new asphalt in its place, which keeps the finished level the same and removes what has worn out.
How do I know if I need a patch or a full rebuild?
A surface that is only worn or lightly cracked can often be patched or resurfaced. Cracks in a network, soft spots that move under a foot, or water that keeps coming back usually mean the base under the surface has failed, and then the base has to be dug out and rebuilt.
How long before I can drive on new asphalt?
Asphalt has to cool before it takes traffic. How long that takes depends on how thick it is laid, the weather and the mix, so we tell you on the day when it is safe to use rather than giving a number here.
Can asphalt be laid in the rain?
No. Rain and a wet surface stop the new asphalt bonding to the layer under it, so a job planned for a wet day is moved to the next dry one.
What is spray sealing and when is it used?
Spray sealing sprays a layer of bitumen onto a prepared surface and covers it with stone chips that are rolled in. It is used on rural roads, long driveways and low-traffic roads where a full asphalt surface is more than the job needs.
Do you work on driveways as well as roads and car parks?
Yes. Asphalt driveways, car parks and roads are all on our service list, and so are the roadworks and civil work that sit underneath them.
Do I need council approval before the work starts?
Work on a public road or footpath usually needs permission from the road authority first. Work on private land can need council approval depending on the job. Describe the site when you call and we can tell you what to check.
What should I have ready when I call?
The suburb, roughly how big the area is in metres, what the surface is made of now, what it is used for and what is going wrong with it. That is enough to start a conversation about the job.
Do you do drainage as well as surfacing?
Yes. Stormwater drainage and retaining walls are on our service list, and they are often part of a surfacing job, because water that sits on or under a surface is what breaks it up.
What is asphalt profiling and road milling?
Profiling uses a milling machine to grind the top off an existing asphalt or concrete surface to a set depth and level. It removes a worn layer, corrects the shape of the road, or gets the surface ready for new asphalt.
Can old asphalt be recycled?
Yes. Old asphalt that has been milled or broken out can be crushed and used again as recycled road base, so it does not all have to go to landfill.
Do you build sports courts?
Sports court asphalting is on our service list. Tell us the type of court and the size of the area, and whether it is a new base or an existing court that needs resurfacing.
What does it cost?
The cost depends on the size of the area, how thick the surface is laid, the condition of the base under it and how easy the site is to reach. No two sites are the same, so we do not publish prices. Describe yours and we will talk through what drives it.
Related work
Other jobs we get called out for
kerb and gutter installation
Kerb and gutter installation builds the concrete edge that holds a road or car park in and carries rainwater to the drain, carried out across Sydney and its western, north-western and surrounding suburbs.
Read morestormwater drainage and retaining walls
Stormwater drainage and retaining walls move rainwater away from paved areas and hold back sloping ground, carried out across Sydney and its western, north-western and surrounding suburbs.
Read moresports court asphalting
Sports court asphalting lays a smooth, level asphalt surface that sheds water for basketball, netball, tennis and multi-use courts, carried out across Sydney and its western, north-western and surrounding suburbs.
Read moreServing Riverstone and The Surrounding Areas
Where we work
Ready when you are
Book Road Repairs and Pavement Patching in Riverstone Today
Tell us the approximate length and width of the damaged area in metres. A rough figure is fine. We will take it from there and talk through the rest with you.
0468 075 505Monday to Friday 8am to 5pm, Saturday and Sunday closed
Not urgent? Send us the job instead
