Asphalt contractor in Richmond, NSW
Working across Richmond
Richmond sits about 19 metres above sea level on the alluvial flats of the Hawkesbury River, and it is one of the five Macquarie Towns founded around 1811. Work here falls into three groups. There are the older town streets around Windsor Street and Bosworth Street, where heritage-listed houses and shops line the road. There are the rural roads that leave town, such as Bells Line of Road, Londonderry Road and Castlereagh Road. And there is farm and campus land, including a university campus of around 1,300 hectares.
Heritage streets mean kerbside parking, shopfront deliveries and trees close to the road. Before we plan a visit we ask who holds the gate key, whether the road belongs to council or to the state, and where the services run, because old town streets can have pipes and cables laid over many decades. Some of the roads out of town are classified routes, so the road authority may need to be asked before we set up traffic control. On a rural lane, the first question is usually whether a truck can turn around.
The ground is river alluvium, sediment laid down by floods, and Richmond is described as flood prone. We cannot tell how deep or how firm that ground is by looking from the kerb. On flat floodplain land, water that sits in the base is a common reason a surface breaks up, so we look at the base and the drainage before we talk about asphalt. What we find once the old surface is off decides the build-up.
What we do here most
What Richmond keeps needing
Almost every job here comes back to water in the ground. A surface lasts only as long as the base under it stays firm.
Rural Road & Driveway Sealing
Sealing a long lane across flat farmland
A gravel lane across flat land is soft after rain and corrugated in dry spells. A sealed lane needs a firm, shaped and compacted base first, with a fall so water leaves the surface. Then bitumen is sprayed and covered with stone. We also check whether a truck can turn at the far end, because a seal is only as good as the base under it.
Pothole repairs
Potholes after floodwater has left a road
Water that sits on a road gets into cracks and softens the base underneath. When traffic returns, the surface breaks and a pothole opens. We cut the damaged patch square, remove the wet and loose material, and rebuild the layers before new asphalt goes in. If the base is soft well beyond the hole, a small patch will not hold, and we will say so.
Car Park Resurfacing
Worn car park behind older town shopfronts
Rear car parks behind older shopfronts often carry delivery trucks as well as cars. The surface wears in the wheel paths and cracks around drain pits and tree roots. We repair the failed patches, then lay new asphalt over the whole surface. We talk through the stages with the site manager so access to the shops is planned before we start.
Road Base & Sub-Base Construction
Rebuilding a soft base on floodplain ground
On river flats the trouble is often not the asphalt but the layers beneath it. If the sub-base holds water, a new surface laid over it will crack again. We dig out the soft material, build up compacted layers of road base and check that the water has a way out. What we find once the old surface is off decides how deep that goes.
If it is urgent
If a pothole opens up on a Richmond road
- 1Keep people and vehicles clear of the hole, and note its size, its depth and where it sits on the road.
- 2Do not fill it with loose soil, sand or gravel, because water will wash it straight back out.
- 3Tell us whether the road has been under floodwater recently and whether it is a council road, a state road or a private lane.
Common questions
Frequently Asked Questions
Which suburbs do you cover?
We work across Sydney and the surrounding suburbs, and the service areas page lists twenty-one of them, from Windsor and Richmond in the north-west to Liverpool and Narellan in the south-west. If yours is not listed it is still worth asking, because the list is where we work most often rather than a boundary.
What hours are you open?
We are open Monday to Friday, 8am to 5pm, and closed on Saturday and Sunday. Ring in those hours and tell us the suburb and what the surface is used for.
What is the difference between resurfacing and mill and fill?
Resurfacing lays new asphalt over the existing surface after it has been cleaned and repaired. Mill and fill first grinds off the top layer of old asphalt, then lays new asphalt in its place, which keeps the finished level the same and removes what has worn out.
How do I know if I need a patch or a full rebuild?
A surface that is only worn or lightly cracked can often be patched or resurfaced. Cracks in a network, soft spots that move under a foot, or water that keeps coming back usually mean the base under the surface has failed, and then the base has to be dug out and rebuilt.
How long before I can drive on new asphalt?
Asphalt has to cool before it takes traffic. How long that takes depends on how thick it is laid, the weather and the mix, so we tell you on the day when it is safe to use rather than giving a number here.
Can asphalt be laid in the rain?
No. Rain and a wet surface stop the new asphalt bonding to the layer under it, so a job planned for a wet day is moved to the next dry one.
What is spray sealing and when is it used?
Spray sealing sprays a layer of bitumen onto a prepared surface and covers it with stone chips that are rolled in. It is used on rural roads, long driveways and low-traffic roads where a full asphalt surface is more than the job needs.
Do you work on driveways as well as roads and car parks?
Yes. Asphalt driveways, car parks and roads are all on our service list, and so are the roadworks and civil work that sit underneath them.
Do I need council approval before the work starts?
Work on a public road or footpath usually needs permission from the road authority first. Work on private land can need council approval depending on the job. Describe the site when you call and we can tell you what to check.
What should I have ready when I call?
The suburb, roughly how big the area is in metres, what the surface is made of now, what it is used for and what is going wrong with it. That is enough to start a conversation about the job.
Do you do drainage as well as surfacing?
Yes. Stormwater drainage and retaining walls are on our service list, and they are often part of a surfacing job, because water that sits on or under a surface is what breaks it up.
What is asphalt profiling and road milling?
Profiling uses a milling machine to grind the top off an existing asphalt or concrete surface to a set depth and level. It removes a worn layer, corrects the shape of the road, or gets the surface ready for new asphalt.
Can old asphalt be recycled?
Yes. Old asphalt that has been milled or broken out can be crushed and used again as recycled road base, so it does not all have to go to landfill.
Do you build sports courts?
Sports court asphalting is on our service list. Tell us the type of court and the size of the area, and whether it is a new base or an existing court that needs resurfacing.
What does it cost?
The cost depends on the size of the area, how thick the surface is laid, the condition of the base under it and how easy the site is to reach. No two sites are the same, so we do not publish prices. Describe yours and we will talk through what drives it.
Everything we do here
Services in Richmond, NSW
Here is everything we do, and on the Richmond flats the base and drainage work matters as much as the surfacing.
Also nearby
We work in these suburbs too
Local, and on the phone
Planning a job in Richmond
Tell us the road name and whether it is a council road, a state road or a private lane or yard. That decides whether we plan around traffic control, a truck turning area or soft ground. Type it into the form and we will take it from there.
0468 075 505Monday to Friday 8am to 5pm, Saturday and Sunday closed
Not urgent? Send us the job instead
