Asphalt contractor in Kellyville, NSW

Working across Kellyville

Kellyville was semi-rural for most of the 20th century. Around Acres Road, about 900 homes went up between the 1960s and 1980s, in the part locals call the Village. Newer estates have since filled the land around it, from leafy lots of 450 to 2,000 square metres to smaller lots of 450 to 600 square metres near the North-west T-Way. The neighbouring North Kellyville precinct lies between Smalls Creek and Cattai Creek and is expected to hold about 7,200 dwellings.

In a new estate the roads are often freshly built and the pipes and pits underneath them are new, so we ask for the plans before we cut or compact near them. On an active site the builder or developer holds the key, and a site supervisor decides when a road is open. Windsor Road, Old Windsor Road and Withers Road carry heavy traffic, so work near them may need traffic control and approval from council or the road authority.

Much of the newer housing sits on lots with a high house-to-land ratio, so yards are small and there is little room to stage a truck. The ground slopes, and creek banks carry remnant bushland. Cattai Creek runs along the eastern and northern edge of North Kellyville, and some homes sit beside creeks such as Caddies Creek. Lots run from small estate blocks to larger semi-rural land, so a driveway job can mean a short apron or a long lane.

What we do here most

What Kellyville keeps needing

Kellyville is mid-change, so jobs split between new ground that has never had a surface and older land with worn drives. Both come down to slope and water.

Subdivision Road Construction

Forming a new estate street on sloping ground

A new street starts with stripped ground and a subgrade that has to be tested for soft spots. Pipes and pits go in first, then the compacted base, then kerb and asphalt. On a slope, getting the falls right decides where the water goes in the first big storm. Council has to be happy with the street before it takes it over.

Asphalt Driveway Construction

A short driveway on a small estate lot

On a small lot the driveway is short, the setbacks are tight and the crossover meets a council footpath. There is little room to stack material or turn a machine, so the order of work matters. We compact the base in thin layers and lay the asphalt to a fall away from the garage. Access for the builder's other trades is planned first.

Stormwater Drainage & Retaining Walls

Stormwater and a retaining wall on a creek lot

A lot beside a creek or on a slope has to move water without sending it onto a neighbour. We look at where runoff arrives and where it can leave, then place pits, pipes and a wall to suit. The wall's footing and drainage behind it matter as much as how it looks. Both show once the ground is opened up.

Rural Road & Driveway Sealing

Sealing a long lane on semi-rural land

Where larger blocks remain, a long gravel lane gets rutted and loses its shape. We reshape it, compact the base and spray a bitumen seal covered with stone. Falls and side drains do most of the work of keeping it intact. A turning area at the house end is worth planning at the start.

If it is urgent

If a pothole opens up on a Kellyville road

  1. 1Keep people and vehicles clear of the hole, and note its size and where it sits on the road or driveway.
  2. 2Do not fill it with loose soil or sand, because runoff on a sloping road will carry it away.
  3. 3Tell us whether it is on an estate street, a main road or a rural lane, and whether you know if council or the road authority looks after it.
Call 0468 075 505

Common questions

Frequently Asked Questions

Which suburbs do you cover?

We work across Sydney and the surrounding suburbs, and the service areas page lists twenty-one of them, from Windsor and Richmond in the north-west to Liverpool and Narellan in the south-west. If yours is not listed it is still worth asking, because the list is where we work most often rather than a boundary.

What hours are you open?

We are open Monday to Friday, 8am to 5pm, and closed on Saturday and Sunday. Ring in those hours and tell us the suburb and what the surface is used for.

What is the difference between resurfacing and mill and fill?

Resurfacing lays new asphalt over the existing surface after it has been cleaned and repaired. Mill and fill first grinds off the top layer of old asphalt, then lays new asphalt in its place, which keeps the finished level the same and removes what has worn out.

How do I know if I need a patch or a full rebuild?

A surface that is only worn or lightly cracked can often be patched or resurfaced. Cracks in a network, soft spots that move under a foot, or water that keeps coming back usually mean the base under the surface has failed, and then the base has to be dug out and rebuilt.

How long before I can drive on new asphalt?

Asphalt has to cool before it takes traffic. How long that takes depends on how thick it is laid, the weather and the mix, so we tell you on the day when it is safe to use rather than giving a number here.

Can asphalt be laid in the rain?

No. Rain and a wet surface stop the new asphalt bonding to the layer under it, so a job planned for a wet day is moved to the next dry one.

What is spray sealing and when is it used?

Spray sealing sprays a layer of bitumen onto a prepared surface and covers it with stone chips that are rolled in. It is used on rural roads, long driveways and low-traffic roads where a full asphalt surface is more than the job needs.

Do you work on driveways as well as roads and car parks?

Yes. Asphalt driveways, car parks and roads are all on our service list, and so are the roadworks and civil work that sit underneath them.

Do I need council approval before the work starts?

Work on a public road or footpath usually needs permission from the road authority first. Work on private land can need council approval depending on the job. Describe the site when you call and we can tell you what to check.

What should I have ready when I call?

The suburb, roughly how big the area is in metres, what the surface is made of now, what it is used for and what is going wrong with it. That is enough to start a conversation about the job.

Do you do drainage as well as surfacing?

Yes. Stormwater drainage and retaining walls are on our service list, and they are often part of a surfacing job, because water that sits on or under a surface is what breaks it up.

What is asphalt profiling and road milling?

Profiling uses a milling machine to grind the top off an existing asphalt or concrete surface to a set depth and level. It removes a worn layer, corrects the shape of the road, or gets the surface ready for new asphalt.

Can old asphalt be recycled?

Yes. Old asphalt that has been milled or broken out can be crushed and used again as recycled road base, so it does not all have to go to landfill.

Do you build sports courts?

Sports court asphalting is on our service list. Tell us the type of court and the size of the area, and whether it is a new base or an existing court that needs resurfacing.

What does it cost?

The cost depends on the size of the area, how thick the surface is laid, the condition of the base under it and how easy the site is to reach. No two sites are the same, so we do not publish prices. Describe yours and we will talk through what drives it.

Local, and on the phone

Planning a job in Kellyville

Tell us whether the site is a new estate lot, an older house block or a semi-rural lane. That decides whether we plan around a short driveway, a truck turning area or a long run of base. Type it into the form with the street name.

0468 075 505

Monday to Friday 8am to 5pm, Saturday and Sunday closed

Not urgent? Send us the job instead