Asphalt contractor in Blacktown, NSW

Working across Blacktown

Blacktown is about 34 kilometres west of the Sydney CBD and works as a commercial hub for Western Sydney. The centre around the railway station holds the council offices, a courthouse, a hospital, a university campus, a large shopping centre and a bus interchange. Around that core, the suburb saw large suburban development in the 1950s and 1960s. The wider council area also has industrial precincts, including Blacktown north and south, and rural land in its north.

In and around the centre, pavement work is mostly car parks, access lanes and loading areas that many people share, so staging has to work around opening hours and foot traffic. Property and strata managers usually hold the keys. Roads in the centre carry buses and trucks, so council or the road authority may need to approve traffic control first. Services sit close together under an established centre, and we ask for plans before we cut.

The Blacktown soil landscape is formed on Wianamatta Group shale, which weathers to a clay that swells when wet, shrinks when dry and drains slowly. That movement cracks asphalt laid over a thin or poorly drained base. Streets and driveways laid in the 1950s and 1960s growth have had decades of traffic over that clay. Council describes two kinds of flooding here, creeks breaking their banks and stormwater running overland when pipes cannot cope.

What we do here most

What Blacktown keeps needing

A busy centre, mid-century streets and industrial lots all put constant traffic on the same clay. Each job below is about surfaces that never get a rest.

Car Park Resurfacing

Resurfacing a busy commercial car park in stages

A car park near the centre rarely closes. We split it into sections so part stays open while the rest is repaired and resurfaced. Failed patches over soft clay come out first, and the new asphalt goes over the whole area. Delivery access and the manager's opening hours decide the order.

Asphalt Profiling & Road Milling

Milling a worn street before it is relaid

When a street surface has cracked and ruts have formed, we mill the worn layer off so the new asphalt goes down at the right level against the kerb. We cut the edges square with a saw before milling starts. Milling also shows the layer underneath, and what that shows decides if any base repair is needed.

Road repairs

Cracked street edges where clay has moved

Clay swells and shrinks with the weather, and the edge of a street is where that movement shows first. Cracks open, water gets in and the break widens. We cut out the failed strip, rebuild the base beneath it and lay new asphalt to meet the old. If the cause is a blocked drain, that has to be fixed too.

Commercial Asphalting

Hardstand and a truck lane for an industrial lot

An industrial lot needs a base built for heavy wheels, with falls that carry water to the pits. Truck turning paths take the most punishment, so we plan them first and lay the asphalt to suit. Gates, docks and existing levels set the heights. We ask what loads the yard will carry before talking about the build-up.

If it is urgent

If a pothole opens up on a Blacktown street

  1. 1Keep people and vehicles clear of the hole, and note its size and where it sits.
  2. 2Do not fill it with loose soil or sand, because on clay ground water gets under it and washes it out.
  3. 3Tell us whether it is in a public street, a car park or an industrial yard, and whether water has been lying near it.
Call 0468 075 505

Common questions

Frequently Asked Questions

Which suburbs do you cover?

We work across Sydney and the surrounding suburbs, and the service areas page lists twenty-one of them, from Windsor and Richmond in the north-west to Liverpool and Narellan in the south-west. If yours is not listed it is still worth asking, because the list is where we work most often rather than a boundary.

What hours are you open?

We are open Monday to Friday, 8am to 5pm, and closed on Saturday and Sunday. Ring in those hours and tell us the suburb and what the surface is used for.

What is the difference between resurfacing and mill and fill?

Resurfacing lays new asphalt over the existing surface after it has been cleaned and repaired. Mill and fill first grinds off the top layer of old asphalt, then lays new asphalt in its place, which keeps the finished level the same and removes what has worn out.

How do I know if I need a patch or a full rebuild?

A surface that is only worn or lightly cracked can often be patched or resurfaced. Cracks in a network, soft spots that move under a foot, or water that keeps coming back usually mean the base under the surface has failed, and then the base has to be dug out and rebuilt.

How long before I can drive on new asphalt?

Asphalt has to cool before it takes traffic. How long that takes depends on how thick it is laid, the weather and the mix, so we tell you on the day when it is safe to use rather than giving a number here.

Can asphalt be laid in the rain?

No. Rain and a wet surface stop the new asphalt bonding to the layer under it, so a job planned for a wet day is moved to the next dry one.

What is spray sealing and when is it used?

Spray sealing sprays a layer of bitumen onto a prepared surface and covers it with stone chips that are rolled in. It is used on rural roads, long driveways and low-traffic roads where a full asphalt surface is more than the job needs.

Do you work on driveways as well as roads and car parks?

Yes. Asphalt driveways, car parks and roads are all on our service list, and so are the roadworks and civil work that sit underneath them.

Do I need council approval before the work starts?

Work on a public road or footpath usually needs permission from the road authority first. Work on private land can need council approval depending on the job. Describe the site when you call and we can tell you what to check.

What should I have ready when I call?

The suburb, roughly how big the area is in metres, what the surface is made of now, what it is used for and what is going wrong with it. That is enough to start a conversation about the job.

Do you do drainage as well as surfacing?

Yes. Stormwater drainage and retaining walls are on our service list, and they are often part of a surfacing job, because water that sits on or under a surface is what breaks it up.

What is asphalt profiling and road milling?

Profiling uses a milling machine to grind the top off an existing asphalt or concrete surface to a set depth and level. It removes a worn layer, corrects the shape of the road, or gets the surface ready for new asphalt.

Can old asphalt be recycled?

Yes. Old asphalt that has been milled or broken out can be crushed and used again as recycled road base, so it does not all have to go to landfill.

Do you build sports courts?

Sports court asphalting is on our service list. Tell us the type of court and the size of the area, and whether it is a new base or an existing court that needs resurfacing.

What does it cost?

The cost depends on the size of the area, how thick the surface is laid, the condition of the base under it and how easy the site is to reach. No two sites are the same, so we do not publish prices. Describe yours and we will talk through what drives it.

Local, and on the phone

Planning a job in Blacktown

Tell us what kind of site it is, whether a street, a commercial car park or an industrial yard, and which hours it is in use. That decides how we plan staging and access. Type it into the form with the street name.

0468 075 505

Monday to Friday 8am to 5pm, Saturday and Sunday closed

Not urgent? Send us the job instead