Mill and Fill Asphalt Repairs in Riverstone, NSW
What is included
What Is Included in Our Mill and Fill Asphalt Repairs
- We look at the damaged area and mark a clean square or rectangle around it.
- The edges are cut square with a saw so the new asphalt has a straight, firm edge to meet.
- The marked area is milled down to the agreed depth, and the loose material is loaded and taken away.
- If the base underneath is soft or wet, that part is dug out and rebuilt before anything goes back in.
- The milled surface and edges are swept clean and sprayed with bitumen emulsion so the new asphalt bonds.
- Hot asphalt is spread into the milled area and filled to match the level of the surface around it.
- It is rolled while hot, and the joins at the edges are finished by hand.
- We sweep the area and show you where the new asphalt meets the old surface.
Why us
Why Choose Us for Mill and Fill Asphalt Repairs?
Accountable for every job, long after the day
Every mill and fill asphalting job is done by the people who will still be here next year.
Tested and signed off before we leave
Everything we touch on your mill and fill asphalting is tested before we go, you get walked through exactly what was done.
Local asphalt contractors, not a call centre
An asphalt contractor answers the phone and the same faces come back if the job runs over a day.
How the job runs
The edge cut decides whether the patch holds
Describing the damaged patch
Tell us where the damage is, how big it is and what it looks like: cracked, sunken, potholed or broken up. Also say what drives over it. We use this to judge whether a mill and fill will fix it or whether the problem goes deeper into the base.
Marking the patch on site
We look at the damage and mark the area to be removed. It is usually bigger than the part you can see, so the new edge sits in sound asphalt. We agree the depth and what to do if the base underneath turns out to be soft.
Cutting, filling and handover
We saw the edges, mill out the marked area and load the old material away. The surface is cleaned, sprayed with bond coat, then filled with hot asphalt and rolled level with the old surface. We show you the patch before we leave and tell you when traffic can use it.
Common questions
Frequently Asked Questions
Which suburbs do you cover?
We work across Sydney and the surrounding suburbs, and the service areas page lists twenty-one of them, from Windsor and Richmond in the north-west to Liverpool and Narellan in the south-west. If yours is not listed it is still worth asking, because the list is where we work most often rather than a boundary.
What hours are you open?
We are open Monday to Friday, 8am to 5pm, and closed on Saturday and Sunday. Ring in those hours and tell us the suburb and what the surface is used for.
What is the difference between resurfacing and mill and fill?
Resurfacing lays new asphalt over the existing surface after it has been cleaned and repaired. Mill and fill first grinds off the top layer of old asphalt, then lays new asphalt in its place, which keeps the finished level the same and removes what has worn out.
How do I know if I need a patch or a full rebuild?
A surface that is only worn or lightly cracked can often be patched or resurfaced. Cracks in a network, soft spots that move under a foot, or water that keeps coming back usually mean the base under the surface has failed, and then the base has to be dug out and rebuilt.
How long before I can drive on new asphalt?
Asphalt has to cool before it takes traffic. How long that takes depends on how thick it is laid, the weather and the mix, so we tell you on the day when it is safe to use rather than giving a number here.
Can asphalt be laid in the rain?
No. Rain and a wet surface stop the new asphalt bonding to the layer under it, so a job planned for a wet day is moved to the next dry one.
What is spray sealing and when is it used?
Spray sealing sprays a layer of bitumen onto a prepared surface and covers it with stone chips that are rolled in. It is used on rural roads, long driveways and low-traffic roads where a full asphalt surface is more than the job needs.
Do you work on driveways as well as roads and car parks?
Yes. Asphalt driveways, car parks and roads are all on our service list, and so are the roadworks and civil work that sit underneath them.
Do I need council approval before the work starts?
Work on a public road or footpath usually needs permission from the road authority first. Work on private land can need council approval depending on the job. Describe the site when you call and we can tell you what to check.
What should I have ready when I call?
The suburb, roughly how big the area is in metres, what the surface is made of now, what it is used for and what is going wrong with it. That is enough to start a conversation about the job.
Do you do drainage as well as surfacing?
Yes. Stormwater drainage and retaining walls are on our service list, and they are often part of a surfacing job, because water that sits on or under a surface is what breaks it up.
What is asphalt profiling and road milling?
Profiling uses a milling machine to grind the top off an existing asphalt or concrete surface to a set depth and level. It removes a worn layer, corrects the shape of the road, or gets the surface ready for new asphalt.
Can old asphalt be recycled?
Yes. Old asphalt that has been milled or broken out can be crushed and used again as recycled road base, so it does not all have to go to landfill.
Do you build sports courts?
Sports court asphalting is on our service list. Tell us the type of court and the size of the area, and whether it is a new base or an existing court that needs resurfacing.
What does it cost?
The cost depends on the size of the area, how thick the surface is laid, the condition of the base under it and how easy the site is to reach. No two sites are the same, so we do not publish prices. Describe yours and we will talk through what drives it.
Related work
Other jobs we get called out for
asphalt pavement restoration
Asphalt pavement restoration is the repair of a worn or cracked asphalt surface by cutting out failed areas, fixing the base and laying new asphalt, carried out across Sydney and its western, north-western and surrounding suburbs.
Read morecar park asphalting and construction
Car park asphalting and construction is building a new car park from the ground up, with a compacted rock base and a laid asphalt surface, carried out across Sydney and its western, north-western and surrounding suburbs.
Read morecar park resurfacing
Car park resurfacing puts a fresh asphalt layer over a worn car park once the failed areas are repaired, and is carried out across Sydney and its western, north-western and surrounding suburbs.
Read moreServing Riverstone and The Surrounding Areas
Where we work
Ready when you are
Book Mill and Fill Asphalt Repairs in Riverstone Today
Type roughly how big the damaged patch is in metres, for example 4 by 3. That tells us whether this is a small repair or a larger section. We take it from there.
0468 075 505Monday to Friday 8am to 5pm, Saturday and Sunday closed
Not urgent? Send us the job instead
