Asphalt contractor in Arndell Park, NSW
Working across Arndell Park
Arndell Park is a predominantly industrial suburb, and it counted only six residents at the 2021 census. That tells you what the paving work here is. It is factory and warehouse frontage, loading yards, estate roads and the car park of the retail mall, which has a discount supermarket, a medical centre, a bottle shop and food outlets. Almost nobody lives on these surfaces, so the wear comes from trucks, vans and shoppers' cars, not from household traffic.
Industrial sites here usually run to a roster. Gates may be locked outside trading hours, and the person who holds the key is often the tenant, the landlord or a managing agent, not the person who rang us. Loading docks and truck turning areas have to stay clear on delivery days, so work is often planned in stages around them. Yards also carry stormwater pits, power and communications lines, and these get located before any cutting or digging starts.
Wear on industrial hardstand shows up as ruts where trucks turn on a tight radius, cracking across the wheel paths, and ravelling where diesel and oil have softened the binder. A retail car park wears differently, with small cracks near trolley bays and speed humps and faded line marking. Whether the base under either one is still sound only shows once the old surface is off, so we say that up front instead of guessing.
What we do here most
What Arndell Park yards keep needing
Heavy wheels turn in the same places every day, so the damage lands in the same places too.
Commercial Asphalting
Truck turning area at a warehouse yard
A yard where semi-trailers swing round the same corner all day ends up with ruts and shoved asphalt right at the turn. We would look at where the wheels actually track, cut out the failed section square, and lay new asphalt there. If the base has gone soft underneath, that shows once the old surface is lifted.
Car Park Resurfacing
Worn shopper car park near the entry lane
A mall car park wears fastest where cars queue, turn and brake, which is usually the entry lane and the rows closest to the doors. Cracks open and the line marking fades. If the base is sound, a new wearing surface over the old one can make sense. Whether the base needs work shows once the old surface is looked at.
Mill & Fill Asphalting
Rutted wheel paths at a loading dock apron
Where trucks reverse into a dock and pull out again, the asphalt can rut and ridge in two lines. We mill that layer off so the new asphalt does not sit on a damaged surface, then fill it back to the original level. Keeping the level matters so water still runs away from the dock door.
Road Base & Sub-Base Construction
New hardstand where a lot is extended
When a tenant wants more truck parking or a wider yard, the asphalt is the last step. First the area is shaped and the road base laid in compacted layers, because trailers sit loaded on one spot for long periods. Thickness depends on the ground and the loads, and both are confirmed on site, not assumed.
If it is urgent
If a pothole opens up in an Arndell Park yard or estate road
- 1Keep people and vehicles clear of the hole, and note how wide and deep it is and where it sits in the yard or on the road.
- 2Do not fill it with loose soil, sand or rubble, because the next truck pulls it straight out again.
- 3Tell us when you call whether it is at a loading dock, a truck turning area, a car park or a public estate road, and who holds the gate key.
Common questions
Frequently Asked Questions
Which suburbs do you cover?
We work across Sydney and the surrounding suburbs, and the service areas page lists twenty-one of them, from Windsor and Richmond in the north-west to Liverpool and Narellan in the south-west. If yours is not listed it is still worth asking, because the list is where we work most often rather than a boundary.
What hours are you open?
We are open Monday to Friday, 8am to 5pm, and closed on Saturday and Sunday. Ring in those hours and tell us the suburb and what the surface is used for.
What is the difference between resurfacing and mill and fill?
Resurfacing lays new asphalt over the existing surface after it has been cleaned and repaired. Mill and fill first grinds off the top layer of old asphalt, then lays new asphalt in its place, which keeps the finished level the same and removes what has worn out.
How do I know if I need a patch or a full rebuild?
A surface that is only worn or lightly cracked can often be patched or resurfaced. Cracks in a network, soft spots that move under a foot, or water that keeps coming back usually mean the base under the surface has failed, and then the base has to be dug out and rebuilt.
How long before I can drive on new asphalt?
Asphalt has to cool before it takes traffic. How long that takes depends on how thick it is laid, the weather and the mix, so we tell you on the day when it is safe to use rather than giving a number here.
Can asphalt be laid in the rain?
No. Rain and a wet surface stop the new asphalt bonding to the layer under it, so a job planned for a wet day is moved to the next dry one.
What is spray sealing and when is it used?
Spray sealing sprays a layer of bitumen onto a prepared surface and covers it with stone chips that are rolled in. It is used on rural roads, long driveways and low-traffic roads where a full asphalt surface is more than the job needs.
Do you work on driveways as well as roads and car parks?
Yes. Asphalt driveways, car parks and roads are all on our service list, and so are the roadworks and civil work that sit underneath them.
Do I need council approval before the work starts?
Work on a public road or footpath usually needs permission from the road authority first. Work on private land can need council approval depending on the job. Describe the site when you call and we can tell you what to check.
What should I have ready when I call?
The suburb, roughly how big the area is in metres, what the surface is made of now, what it is used for and what is going wrong with it. That is enough to start a conversation about the job.
Do you do drainage as well as surfacing?
Yes. Stormwater drainage and retaining walls are on our service list, and they are often part of a surfacing job, because water that sits on or under a surface is what breaks it up.
What is asphalt profiling and road milling?
Profiling uses a milling machine to grind the top off an existing asphalt or concrete surface to a set depth and level. It removes a worn layer, corrects the shape of the road, or gets the surface ready for new asphalt.
Can old asphalt be recycled?
Yes. Old asphalt that has been milled or broken out can be crushed and used again as recycled road base, so it does not all have to go to landfill.
Do you build sports courts?
Sports court asphalting is on our service list. Tell us the type of court and the size of the area, and whether it is a new base or an existing court that needs resurfacing.
What does it cost?
The cost depends on the size of the area, how thick the surface is laid, the condition of the base under it and how easy the site is to reach. No two sites are the same, so we do not publish prices. Describe yours and we will talk through what drives it.
Everything we do here
Services in Arndell Park, NSW
These are the services that suit the heavy yards, loading areas and retail car parks that make up Arndell Park.
Also nearby
We work in these suburbs too
Local, and on the phone
Tell us about your Arndell Park site
Tell us what the surface is used for: truck yard, loading dock, estate road or shopper car park. That decides how heavy the base needs to be and how a visit is planned. Type a few lines in your message, with the street and the weekday that suits for us to meet you there.
0468 075 505Monday to Friday 8am to 5pm, Saturday and Sunday closed
Not urgent? Send us the job instead
