Asphalt contractor in Liverpool, NSW
Working across Liverpool
Liverpool is about 40 km south-west of the Sydney CBD, on the western bank of the Georges River at around 29 m. Macquarie Street is the main retail strip, and the centre was rezoned for mixed use in 2018 to allow more homes, offices and shops. The suburb also has former manufacturing sites and large public housing estates built after the 1960s urban renewal programs. Hume Highway, the M5 and the M7 run through or beside it.
A town centre site means people on foot, traffic control and tight working hours. A car park may stay open in sections, and a street may need approval from council or the road authority before we start. A former factory site is different: it may be a large hardstand with one gate and a manager who holds the key. In either case, we ask where stormwater pits, pipes and other services run before we cut anything.
Council's floodplain pages cover the Georges River, and the main river floodplain runs between Glenfield and East Hills. Ground near the river and on flat sites can stay wet. In older streets, surfaces may be worn and kerbs lifted by tree roots. With so many kinds of land in one place, we cannot assume the base. We want to see the surface and how water leaves it first.
What we do here most
What Liverpool keeps needing
Liverpool mixes a growing centre, old factory ground and worn estate streets, and each of them wears its surface in a different way.
Car Park Resurfacing
A worn car park in the town centre
A centre car park takes the same turning movements every day. The surface ravels, the line marking fades and low spots hold water. We check the falls, cut out failed patches and resurface in stages so people can still get in and out. Line marking is planned once the new surface is down.
Asphalt Pavement Restoration
An old factory hardstand with failed patches
A former manufacturing site often has a large hardstand that has been patched many times. Cracks, ruts and old repairs show where the base has failed. We look at how the site will be used now, test the base in a few spots, and then decide how much surface to cut out and rebuild.
Stormwater Drainage & Retaining Walls
Drainage for a flat site near the river
Ground near the Georges River floodplain is flat, and water can stay on a site long after rain. A pit and pipe layout has to take it away without sending it onto a neighbour or into a pipe that belongs to someone else. We work out the levels and the discharge point with you, and ask council where needed.
Kerb & Gutter Installation
Replacing lifted kerb in older estate streets
In streets laid out decades ago, kerb and gutter can lift or crack where tree roots push under it. Water then lies in the gutter instead of running to the pit. We cut out the broken length, check the base underneath, and re-form the kerb to a level that drains. Where a tree is the cause, council or the owner decides its future.
If it is urgent
If a pothole opens up on a Liverpool street
- 1Keep people and vehicles clear of the hole, and note its size and where it is, such as the street, the nearest intersection and which lane.
- 2Leave the hole alone and do not fill it with loose soil, sand or gravel, because passing traffic will push it out and the hole will widen.
- 3Tell us when you call whether it is on a council street, a main road such as Hume Highway, or private land such as a car park or yard, and whether water lies there.
Common questions
Frequently Asked Questions
Which suburbs do you cover?
We work across Sydney and the surrounding suburbs, and the service areas page lists twenty-one of them, from Windsor and Richmond in the north-west to Liverpool and Narellan in the south-west. If yours is not listed it is still worth asking, because the list is where we work most often rather than a boundary.
What hours are you open?
We are open Monday to Friday, 8am to 5pm, and closed on Saturday and Sunday. Ring in those hours and tell us the suburb and what the surface is used for.
What is the difference between resurfacing and mill and fill?
Resurfacing lays new asphalt over the existing surface after it has been cleaned and repaired. Mill and fill first grinds off the top layer of old asphalt, then lays new asphalt in its place, which keeps the finished level the same and removes what has worn out.
How do I know if I need a patch or a full rebuild?
A surface that is only worn or lightly cracked can often be patched or resurfaced. Cracks in a network, soft spots that move under a foot, or water that keeps coming back usually mean the base under the surface has failed, and then the base has to be dug out and rebuilt.
How long before I can drive on new asphalt?
Asphalt has to cool before it takes traffic. How long that takes depends on how thick it is laid, the weather and the mix, so we tell you on the day when it is safe to use rather than giving a number here.
Can asphalt be laid in the rain?
No. Rain and a wet surface stop the new asphalt bonding to the layer under it, so a job planned for a wet day is moved to the next dry one.
What is spray sealing and when is it used?
Spray sealing sprays a layer of bitumen onto a prepared surface and covers it with stone chips that are rolled in. It is used on rural roads, long driveways and low-traffic roads where a full asphalt surface is more than the job needs.
Do you work on driveways as well as roads and car parks?
Yes. Asphalt driveways, car parks and roads are all on our service list, and so are the roadworks and civil work that sit underneath them.
Do I need council approval before the work starts?
Work on a public road or footpath usually needs permission from the road authority first. Work on private land can need council approval depending on the job. Describe the site when you call and we can tell you what to check.
What should I have ready when I call?
The suburb, roughly how big the area is in metres, what the surface is made of now, what it is used for and what is going wrong with it. That is enough to start a conversation about the job.
Do you do drainage as well as surfacing?
Yes. Stormwater drainage and retaining walls are on our service list, and they are often part of a surfacing job, because water that sits on or under a surface is what breaks it up.
What is asphalt profiling and road milling?
Profiling uses a milling machine to grind the top off an existing asphalt or concrete surface to a set depth and level. It removes a worn layer, corrects the shape of the road, or gets the surface ready for new asphalt.
Can old asphalt be recycled?
Yes. Old asphalt that has been milled or broken out can be crushed and used again as recycled road base, so it does not all have to go to landfill.
Do you build sports courts?
Sports court asphalting is on our service list. Tell us the type of court and the size of the area, and whether it is a new base or an existing court that needs resurfacing.
What does it cost?
The cost depends on the size of the area, how thick the surface is laid, the condition of the base under it and how easy the site is to reach. No two sites are the same, so we do not publish prices. Describe yours and we will talk through what drives it.
Everything we do here
Services in Liverpool, NSW
A city centre, old factory ground and estate streets near a river floodplain decide which of our services are most asked about in Liverpool.
Also nearby
We work in these suburbs too
Local, and on the phone
Tell us about your Liverpool site
Type whether the site is a car park, a factory yard, an estate street or a driveway, and who owns it. That one answer decides who we ask first and how a visit here is planned.
0468 075 505Monday to Friday 8am to 5pm, Saturday and Sunday closed
Not urgent? Send us the job instead
