Asphalt contractor in Hornsby, NSW
Working across Hornsby
Hornsby is on Sydney's Upper North Shore, about 23 km north-west of the CBD, and sits on the Hornsby Plateau at around 188 m. The Pacific Highway, Old Pacific Highway and Peats Ferry Road meet near Hookhams Corner, and the railway junction sits in the middle of town. Around that centre are low to medium density streets, apartments beside the line, and bushy western areas close to national parks. Most of our work here is on sloping streets, driveways and lanes.
Sloping land changes how we plan a visit. Driveways run steeply, kerbs are tall on the downhill side, and a road with a bend and a drop has little room for a truck to stop. Traffic control matters where streets are narrow or join a main road, and the road authority or council may need to be asked first. Water, gas and power services run under many streets, so we want to know where they sit before we dig.
Hornsby sits on Hawkesbury Sandstone, with Ashfield Shale in places, and the plateau is cut by creek gullies. Soils on the plateau are generally shallow. Rock can sit close to the surface, which affects digging for drains and walls. Water also runs fast down these slopes and into the creeks. A base that has to carry traffic on a slope needs good drainage across it, or the water undermines the asphalt.
What we do here most
What Hornsby keeps needing
Hornsby's streets run down a sandstone plateau, so water speed and rock decide how each surface holds up.
Asphalt Driveway Construction
A steep driveway on a sloping bush lot
A driveway on a slope needs a firm base and a surface that does not shed water straight onto the footpath. We work out the grade, the drainage across the surface and the drop at the road edge before we cut. The sandstone below may be hard to dig, and how hard only shows once the old surface is off.
Bulk & Detailed Excavation
Digging for a drain or wall through sandstone
On the plateau, rock can sit shallow, so digging for a drain, a wall footing or a new driveway base may hit sandstone. We do not know where until we dig. We plan around services that run close to the surface on slopes, and we talk to you before we change the layout if rock turns up.
Stormwater Drainage & Retaining Walls
Water running off a slope towards a gully
Rain on a steep street collects fast and washes across driveways and onto lower lots. A pit and pipe at the right spot catches it before it goes onto the neighbour's block. A retaining wall holds the cut behind a driveway or yard. We check where the water is allowed to go before we choose either.
Road repairs
Worn older streets with bush on both sides
Streets in the older bushy parts of Hornsby wear along the edges, where trees grow close and roots can lift the kerb and cracks run along the gutter. We cut out the failed edge, repair the base underneath and re-lay the surface. If roots are the cause, the tree owner or council decides what happens to the tree, not us.
If it is urgent
If a pothole opens up on a Hornsby street
- 1Keep people and vehicles clear of the hole, and note its size, its depth and which side of the street it is on, especially on a bend or slope.
- 2Leave the hole alone and do not fill it with loose soil, sand or gravel, because on a slope rain will wash it down the street.
- 3Tell us when you call how steep the street is, whether water runs across the spot, and whether it is a council street, a highway side road or private.
Common questions
Frequently Asked Questions
Which suburbs do you cover?
We work across Sydney and the surrounding suburbs, and the service areas page lists twenty-one of them, from Windsor and Richmond in the north-west to Liverpool and Narellan in the south-west. If yours is not listed it is still worth asking, because the list is where we work most often rather than a boundary.
What hours are you open?
We are open Monday to Friday, 8am to 5pm, and closed on Saturday and Sunday. Ring in those hours and tell us the suburb and what the surface is used for.
What is the difference between resurfacing and mill and fill?
Resurfacing lays new asphalt over the existing surface after it has been cleaned and repaired. Mill and fill first grinds off the top layer of old asphalt, then lays new asphalt in its place, which keeps the finished level the same and removes what has worn out.
How do I know if I need a patch or a full rebuild?
A surface that is only worn or lightly cracked can often be patched or resurfaced. Cracks in a network, soft spots that move under a foot, or water that keeps coming back usually mean the base under the surface has failed, and then the base has to be dug out and rebuilt.
How long before I can drive on new asphalt?
Asphalt has to cool before it takes traffic. How long that takes depends on how thick it is laid, the weather and the mix, so we tell you on the day when it is safe to use rather than giving a number here.
Can asphalt be laid in the rain?
No. Rain and a wet surface stop the new asphalt bonding to the layer under it, so a job planned for a wet day is moved to the next dry one.
What is spray sealing and when is it used?
Spray sealing sprays a layer of bitumen onto a prepared surface and covers it with stone chips that are rolled in. It is used on rural roads, long driveways and low-traffic roads where a full asphalt surface is more than the job needs.
Do you work on driveways as well as roads and car parks?
Yes. Asphalt driveways, car parks and roads are all on our service list, and so are the roadworks and civil work that sit underneath them.
Do I need council approval before the work starts?
Work on a public road or footpath usually needs permission from the road authority first. Work on private land can need council approval depending on the job. Describe the site when you call and we can tell you what to check.
What should I have ready when I call?
The suburb, roughly how big the area is in metres, what the surface is made of now, what it is used for and what is going wrong with it. That is enough to start a conversation about the job.
Do you do drainage as well as surfacing?
Yes. Stormwater drainage and retaining walls are on our service list, and they are often part of a surfacing job, because water that sits on or under a surface is what breaks it up.
What is asphalt profiling and road milling?
Profiling uses a milling machine to grind the top off an existing asphalt or concrete surface to a set depth and level. It removes a worn layer, corrects the shape of the road, or gets the surface ready for new asphalt.
Can old asphalt be recycled?
Yes. Old asphalt that has been milled or broken out can be crushed and used again as recycled road base, so it does not all have to go to landfill.
Do you build sports courts?
Sports court asphalting is on our service list. Tell us the type of court and the size of the area, and whether it is a new base or an existing court that needs resurfacing.
What does it cost?
The cost depends on the size of the area, how thick the surface is laid, the condition of the base under it and how easy the site is to reach. No two sites are the same, so we do not publish prices. Describe yours and we will talk through what drives it.
Everything we do here
Services in Hornsby, NSW
Steep sandstone ground, bushy streets and a busy rail and highway centre shape which of our services get asked about in Hornsby.
Also nearby
We work in these suburbs too
Local, and on the phone
Tell us about your Hornsby site
Type the street or driveway, how steep the surface is, and which way the water runs across it after rain. On a slope that one detail decides the base, the drainage and how we plan access.
0468 075 505Monday to Friday 8am to 5pm, Saturday and Sunday closed
Not urgent? Send us the job instead
