Resurface Worn Asphalt Surfaces in Riverstone, NSW
What is included
What Is Included in Our Resurface Worn Asphalt Surfaces
- We inspect the old surface for cracking, ruts, soft patches and places where water sits.
- Failed patches are cut out square and rebuilt with new base and asphalt before anything goes over them.
- Cracks are cleaned out, and loose or crumbling material is swept away.
- The whole surface is swept clean so nothing sits between the old and new layers.
- Bitumen emulsion is sprayed over the old surface as a tack coat so the new layer bonds to it.
- Hot asphalt is spread over the area at the agreed thickness and rolled while it is still hot.
- We check the new level at kerbs, gutters and pits so water still runs into the drains.
- We sweep up and walk the finished surface with you before we leave.
Why us
Why Choose Us for Resurface Worn Asphalt Surfaces?
Accountable for every job, long after the day
Every asphalt resurfacing job is done by the people who will still be here next year.
Tested and signed off before we leave
Everything we touch on your asphalt resurfacing is tested before we go, you get walked through exactly what was done.
Local asphalt contractors, not a call centre
An asphalt contractor answers the phone and the same faces come back if the job runs over a day.
How the job runs
Resurfacing works when repairs come first
Describing the worn surface
Tell us what you can see: cracks, ruts, potholes, water lying after rain, or a surface that is simply worn smooth. Also tell us what drives on it and how big the area is. We use that to work out whether a new layer can go over it or whether some of it needs to come out first.
Checking what can stay
On site we look at how deep the damage goes. Surface wear can be laid over, but soft or broken ground underneath will come through a new layer, so those patches get dug out. We agree with you which areas are repaired first and where the new layer begins and ends.
Repairs, new layer, handover
We repair the failed spots first, then clean the surface and spray the bond coat. The hot asphalt is spread and rolled over the whole area, and the edges are finished by hand. Before we go, we show you the result and tell you when it can take traffic.
Common questions
Frequently Asked Questions
Which suburbs do you cover?
We work across Sydney and the surrounding suburbs, and the service areas page lists twenty-one of them, from Windsor and Richmond in the north-west to Liverpool and Narellan in the south-west. If yours is not listed it is still worth asking, because the list is where we work most often rather than a boundary.
What hours are you open?
We are open Monday to Friday, 8am to 5pm, and closed on Saturday and Sunday. Ring in those hours and tell us the suburb and what the surface is used for.
What is the difference between resurfacing and mill and fill?
Resurfacing lays new asphalt over the existing surface after it has been cleaned and repaired. Mill and fill first grinds off the top layer of old asphalt, then lays new asphalt in its place, which keeps the finished level the same and removes what has worn out.
How do I know if I need a patch or a full rebuild?
A surface that is only worn or lightly cracked can often be patched or resurfaced. Cracks in a network, soft spots that move under a foot, or water that keeps coming back usually mean the base under the surface has failed, and then the base has to be dug out and rebuilt.
How long before I can drive on new asphalt?
Asphalt has to cool before it takes traffic. How long that takes depends on how thick it is laid, the weather and the mix, so we tell you on the day when it is safe to use rather than giving a number here.
Can asphalt be laid in the rain?
No. Rain and a wet surface stop the new asphalt bonding to the layer under it, so a job planned for a wet day is moved to the next dry one.
What is spray sealing and when is it used?
Spray sealing sprays a layer of bitumen onto a prepared surface and covers it with stone chips that are rolled in. It is used on rural roads, long driveways and low-traffic roads where a full asphalt surface is more than the job needs.
Do you work on driveways as well as roads and car parks?
Yes. Asphalt driveways, car parks and roads are all on our service list, and so are the roadworks and civil work that sit underneath them.
Do I need council approval before the work starts?
Work on a public road or footpath usually needs permission from the road authority first. Work on private land can need council approval depending on the job. Describe the site when you call and we can tell you what to check.
What should I have ready when I call?
The suburb, roughly how big the area is in metres, what the surface is made of now, what it is used for and what is going wrong with it. That is enough to start a conversation about the job.
Do you do drainage as well as surfacing?
Yes. Stormwater drainage and retaining walls are on our service list, and they are often part of a surfacing job, because water that sits on or under a surface is what breaks it up.
What is asphalt profiling and road milling?
Profiling uses a milling machine to grind the top off an existing asphalt or concrete surface to a set depth and level. It removes a worn layer, corrects the shape of the road, or gets the surface ready for new asphalt.
Can old asphalt be recycled?
Yes. Old asphalt that has been milled or broken out can be crushed and used again as recycled road base, so it does not all have to go to landfill.
Do you build sports courts?
Sports court asphalting is on our service list. Tell us the type of court and the size of the area, and whether it is a new base or an existing court that needs resurfacing.
What does it cost?
The cost depends on the size of the area, how thick the surface is laid, the condition of the base under it and how easy the site is to reach. No two sites are the same, so we do not publish prices. Describe yours and we will talk through what drives it.
Related work
Other jobs we get called out for
road construction and roadworks
Building new roads and carrying out roadworks, from earthworks and road base through to the asphalt or sealed surface, carried out across Sydney and its western, north-western and surrounding suburbs.
Read moreasphalt profiling and road milling
Grinding worn or damaged asphalt off to a set depth so the surface can be levelled and relaid, carried out across Sydney and its western, north-western and surrounding suburbs.
Read moremill and fill asphalting
Milling out a damaged section of asphalt and laying new asphalt in the same space so it sits level with the surface around it, carried out across Sydney and its western, north-western and surrounding suburbs.
Read moreServing Riverstone and The Surrounding Areas
Where we work
Ready when you are
Book Resurface Worn Asphalt Surfaces in Riverstone Today
Type what is wrong with the surface now, for example cracking, ruts, potholes or water that lies after rain. That tells us whether a new layer can go straight over it. Size and use can come later.
0468 075 505Monday to Friday 8am to 5pm, Saturday and Sunday closed
Not urgent? Send us the job instead
